How to prepare a seed bed before the planting season
05/02/2021
Preparing the planter for the new season
Before the start of the new sowing season, you need to take care of your agricultural machinery. January-February is the most favorable time for scheduled maintenance of seeders. March will be too late. In the article we will tell you how to troubleshoot a seeder, how to determine which parts need to be replaced and what spare parts you need to buy in order to prepare the equipment for the new season.
At the end of the sowing season, many farmers leave their equipment in the hangar and forget about it until spring. And then, on the eve of the start of the sowing campaign, they begin frantically in an emergency order to look for the necessary parts to restore the efficiency of their equipment.
But it is much better and more efficient to carry out troubleshooting in a timely manner, order and buy the necessary parts, and slowly carry out repairs and maintenance of the seeder.
What is a defect?
Troubleshooting is a preventive inspection of equipment to detect breakdowns, wear and tear, the need to replace worn-out parts.
Inspection of equipment is better to start with an assessment of the general condition of the seeder. First, a specialist mechanic should check the unit for cracks, breakages and deformations visible to the naked eye. After that, it is necessary to inspect the welds, test the hydraulic system, the operation of hydraulic cylinders, row markers, hydraulic hoses and fittings. Do not forget about the pneumatic system, the turbine, check the tightness of the air ducts and the degree of vacuum in the sowing units. The mechanics also need to check backlash, clearances, bolt tightening, lubrication points, etc. in all systems and assemblies.
When to troubleshoot?
It is necessary to prepare the seeder for sowing in advance. When troubleshooting, hidden breakdowns and wear points are detected in time. Their untimely elimination can subsequently lead to more serious breakdowns or poor-quality sowing.
Experts say that the check of the technical condition of the seeder should be carried out "in hot pursuit", i.e. immediately after sowing. While the machine operator remembers all the identified malfunctions and while there is time to eliminate them. If you have not done this in advance, then there is still time to take care of the equipment and prepare it for the new season. Now, in the middle of winter, there is already an increased demand for parts for seeders, but there is not yet such a rush, which will be observed at the end of February.
Preparing the planter for inspection
Before carrying out troubleshooting, first of all, it is necessary to clean the seeder from all dirt and plant residues. To do this, it is washed with a jet of water under pressure and dried with air from the compressor (this will remove water from the parts and assemblies of the seeder).
In general, do not forget that washing and “drying” the seeder after sowing is an elementary rule of operation, which significantly increases its service life and uninterrupted operation.
Where to buy spare parts for a seeder?
Art-Agro wishes your equipment "good health", but in case of breakdowns or when it's time to change consumables, we are ready to offer a full range of spare parts, belts, bearings, filters, lubricants for the seeder from the best world manufacturers. Our managers will help you choose the necessary parts, offer the best price, and arrange fast shipment of the order throughout Ukraine.
Recommended products
Preparing the planter for the new season
Before the start of the new sowing season, you need to take care of your agricultural machinery. January-February is the most favorable time for scheduled maintenance of seeders. March will be too late. In the article we will tell you how to troubleshoot a seeder, how to determine which parts need to be replaced and what spare parts you need to buy in order to prepare the equipment for the new season.
At the end of the sowing season, many farmers leave their equipment in the hangar and forget about it until spring. And then, on the eve of the start of the sowing campaign, they begin frantically in an emergency order to look for the necessary parts to restore the efficiency of their equipment.
But it is much better and more efficient to carry out troubleshooting in a timely manner, order and buy the necessary parts, and slowly carry out repairs and maintenance of the seeder.
What is a defect?
Troubleshooting is a preventive inspection of equipment to detect breakdowns, wear and tear, the need to replace worn-out parts.
Inspection of equipment is better to start with an assessment of the general condition of the seeder. First, a specialist mechanic should check the unit for cracks, breakages and deformations visible to the naked eye. After that, it is necessary to inspect the welds, test the hydraulic system, the operation of hydraulic cylinders, row markers, hydraulic hoses and fittings. Do not forget about the pneumatic system, the turbine, check the tightness of the air ducts and the degree of vacuum in the sowing units. The mechanics also need to check backlash, clearances, bolt tightening, lubrication points, etc. in all systems and assemblies.
When to troubleshoot?
It is necessary to prepare the seeder for sowing in advance. When troubleshooting, hidden breakdowns and wear points are detected in time. Their untimely elimination can subsequently lead to more serious breakdowns or poor-quality sowing.
Experts say that the check of the technical condition of the seeder should be carried out "in hot pursuit", i.e. immediately after sowing. While the machine operator remembers all the identified malfunctions and while there is time to eliminate them. If you have not done this in advance, then there is still time to take care of the equipment and prepare it for the new season. Now, in the middle of winter, there is already an increased demand for parts for seeders, but there is not yet such a rush, which will be observed at the end of February.
Preparing the planter for inspection
Before carrying out troubleshooting, first of all, it is necessary to clean the seeder from all dirt and plant residues. To do this, it is washed with a jet of water under pressure and dried with air from the compressor (this will remove water from the parts and assemblies of the seeder).
In general, do not forget that washing and “drying” the seeder after sowing is an elementary rule of operation, which significantly increases its service life and uninterrupted operation.
Where to buy spare parts for a seeder?
Art-Agro wishes your equipment "good health", but in case of breakdowns or when it's time to change consumables, we are ready to offer a full range of spare parts, belts, bearings, filters, lubricants for the seeder from the best world manufacturers. Our managers will help you choose the necessary parts, offer the best price, and arrange fast shipment of the order throughout Ukraine.
Preparing the planter for the new season
Before the start of the new sowing season, you need to take care of your agricultural machinery. January-February is the most favorable time for scheduled maintenance of seeders. March will be too late. In the article we will tell you how to troubleshoot a seeder, how to determine which parts need to be replaced and what spare parts you need to buy in order to prepare the equipment for the new season.
At the end of the sowing season, many farmers leave their equipment in the hangar and forget about it until spring. And then, on the eve of the start of the sowing campaign, they begin frantically in an emergency order to look for the necessary parts to restore the efficiency of their equipment.
But it is much better and more efficient to carry out troubleshooting in a timely manner, order and buy the necessary parts, and slowly carry out repairs and maintenance of the seeder.
What is a defect?
Troubleshooting is a preventive inspection of equipment to detect breakdowns, wear and tear, the need to replace worn-out parts.
Inspection of equipment is better to start with an assessment of the general condition of the seeder. First, a specialist mechanic should check the unit for cracks, breakages and deformations visible to the naked eye. After that, it is necessary to inspect the welds, test the hydraulic system, the operation of hydraulic cylinders, row markers, hydraulic hoses and fittings. Do not forget about the pneumatic system, the turbine, check the tightness of the air ducts and the degree of vacuum in the sowing units. The mechanics also need to check backlash, clearances, bolt tightening, lubrication points, etc. in all systems and assemblies.
When to troubleshoot?
It is necessary to prepare the seeder for sowing in advance. When troubleshooting, hidden breakdowns and wear points are detected in time. Their untimely elimination can subsequently lead to more serious breakdowns or poor-quality sowing.
Experts say that the check of the technical condition of the seeder should be carried out "in hot pursuit", i.e. immediately after sowing. While the machine operator remembers all the identified malfunctions and while there is time to eliminate them. If you have not done this in advance, then there is still time to take care of the equipment and prepare it for the new season. Now, in the middle of winter, there is already an increased demand for parts for seeders, but there is not yet such a rush, which will be observed at the end of February.
Preparing the planter for inspection
Before carrying out troubleshooting, first of all, it is necessary to clean the seeder from all dirt and plant residues. To do this, it is washed with a jet of water under pressure and dried with air from the compressor (this will remove water from the parts and assemblies of the seeder).
In general, do not forget that washing and “drying” the seeder after sowing is an elementary rule of operation, which significantly increases its service life and uninterrupted operation.
Where to buy spare parts for a seeder?
Art-Agro wishes your equipment "good health", but in case of breakdowns or when it's time to change consumables, we are ready to offer a full range of spare parts, belts, bearings, filters, lubricants for the seeder from the best world manufacturers. Our managers will help you choose the necessary parts, offer the best price, and arrange fast shipment of the order throughout Ukraine.
Preparing the planter for the new season
Before the start of the new sowing season, you need to take care of your agricultural machinery. January-February is the most favorable time for scheduled maintenance of seeders. March will be too late. In the article we will tell you how to troubleshoot a seeder, how to determine which parts need to be replaced and what spare parts you need to buy in order to prepare the equipment for the new season.
At the end of the sowing season, many farmers leave their equipment in the hangar and forget about it until spring. And then, on the eve of the start of the sowing campaign, they begin frantically in an emergency order to look for the necessary parts to restore the efficiency of their equipment.
But it is much better and more efficient to carry out troubleshooting in a timely manner, order and buy the necessary parts, and slowly carry out repairs and maintenance of the seeder.
What is a defect?
Troubleshooting is a preventive inspection of equipment to detect breakdowns, wear and tear, the need to replace worn-out parts.
Inspection of equipment is better to start with an assessment of the general condition of the seeder. First, a specialist mechanic should check the unit for cracks, breakages and deformations visible to the naked eye. After that, it is necessary to inspect the welds, test the hydraulic system, the operation of hydraulic cylinders, row markers, hydraulic hoses and fittings. Do not forget about the pneumatic system, the turbine, check the tightness of the air ducts and the degree of vacuum in the sowing units. The mechanics also need to check backlash, clearances, bolt tightening, lubrication points, etc. in all systems and assemblies.
When to troubleshoot?
It is necessary to prepare the seeder for sowing in advance. When troubleshooting, hidden breakdowns and wear points are detected in time. Their untimely elimination can subsequently lead to more serious breakdowns or poor-quality sowing.
Experts say that the check of the technical condition of the seeder should be carried out "in hot pursuit", i.e. immediately after sowing. While the machine operator remembers all the identified malfunctions and while there is time to eliminate them. If you have not done this in advance, then there is still time to take care of the equipment and prepare it for the new season. Now, in the middle of winter, there is already an increased demand for parts for seeders, but there is not yet such a rush, which will be observed at the end of February.
Preparing the planter for inspection
Before carrying out troubleshooting, first of all, it is necessary to clean the seeder from all dirt and plant residues. To do this, it is washed with a jet of water under pressure and dried with air from the compressor (this will remove water from the parts and assemblies of the seeder).
In general, do not forget that washing and “drying” the seeder after sowing is an elementary rule of operation, which significantly increases its service life and uninterrupted operation.
Where to buy spare parts for a seeder?
Art-Agro wishes your equipment "good health", but in case of breakdowns or when it's time to change consumables, we are ready to offer a full range of spare parts, belts, bearings, filters, lubricants for the seeder from the best world manufacturers. Our managers will help you choose the necessary parts, offer the best price, and arrange fast shipment of the order throughout Ukraine.
Preparing the planter for the new season
Before the start of the new sowing season, you need to take care of your agricultural machinery. January-February is the most favorable time for scheduled maintenance of seeders. March will be too late. In the article we will tell you how to troubleshoot a seeder, how to determine which parts need to be replaced and what spare parts you need to buy in order to prepare the equipment for the new season.
At the end of the sowing season, many farmers leave their equipment in the hangar and forget about it until spring. And then, on the eve of the start of the sowing campaign, they begin frantically in an emergency order to look for the necessary parts to restore the efficiency of their equipment.
But it is much better and more efficient to carry out troubleshooting in a timely manner, order and buy the necessary parts, and slowly carry out repairs and maintenance of the seeder.
What is a defect?
Troubleshooting is a preventive inspection of equipment to detect breakdowns, wear and tear, the need to replace worn-out parts.
Inspection of equipment is better to start with an assessment of the general condition of the seeder. First, a specialist mechanic should check the unit for cracks, breakages and deformations visible to the naked eye. After that, it is necessary to inspect the welds, test the hydraulic system, the operation of hydraulic cylinders, row markers, hydraulic hoses and fittings. Do not forget about the pneumatic system, the turbine, check the tightness of the air ducts and the degree of vacuum in the sowing units. The mechanics also need to check backlash, clearances, bolt tightening, lubrication points, etc. in all systems and assemblies.
When to troubleshoot?
It is necessary to prepare the seeder for sowing in advance. When troubleshooting, hidden breakdowns and wear points are detected in time. Their untimely elimination can subsequently lead to more serious breakdowns or poor-quality sowing.
Experts say that the check of the technical condition of the seeder should be carried out "in hot pursuit", i.e. immediately after sowing. While the machine operator remembers all the identified malfunctions and while there is time to eliminate them. If you have not done this in advance, then there is still time to take care of the equipment and prepare it for the new season. Now, in the middle of winter, there is already an increased demand for parts for seeders, but there is not yet such a rush, which will be observed at the end of February.
Preparing the planter for inspection
Before carrying out troubleshooting, first of all, it is necessary to clean the seeder from all dirt and plant residues. To do this, it is washed with a jet of water under pressure and dried with air from the compressor (this will remove water from the parts and assemblies of the seeder).
In general, do not forget that washing and “drying” the seeder after sowing is an elementary rule of operation, which significantly increases its service life and uninterrupted operation.
Where to buy spare parts for a seeder?
Art-Agro wishes your equipment "good health", but in case of breakdowns or when it's time to change consumables, we are ready to offer a full range of spare parts, belts, bearings, filters, lubricants for the seeder from the best world manufacturers. Our managers will help you choose the necessary parts, offer the best price, and arrange fast shipment of the order throughout Ukraine.